Archiv verlassen und diese Seite im Standarddesign anzeigen : Netzwerkarte
Wie kann ich meine Netzwerkarte auf full duplex 10Mbit stellen ?
http://www.lfs-tipps.de/sections.php?op=viewarticle&artid=69
root@Username/$mii-tool -F 10baseT-HD
SIOCGMIIPHY on 'eth0' failed: Invalid argument
SIOCGMIIPHY on 'eth1' failed: Invalid argument
SIOCGMIIPHY on 'eth2' failed: Invalid argument
SIOCGMIIPHY on 'eth3' failed: Invalid argument
SIOCGMIIPHY on 'eth4' failed: Invalid argument
SIOCGMIIPHY on 'eth5' failed: Invalid argument
SIOCGMIIPHY on 'eth6' failed: Invalid argument
SIOCGMIIPHY on 'eth7' failed: Invalid argument
no MII interfaces found
mm geht das jetzt ??
Hi!
Welche Karte?
Grüße
Manx
Original geschrieben von localhost
root@Username/$mii-tool -F 10baseT-HD
SIOCGMIIPHY on 'eth0' failed: Invalid argument
SIOCGMIIPHY on 'eth1' failed: Invalid argument
SIOCGMIIPHY on 'eth2' failed: Invalid argument
SIOCGMIIPHY on 'eth3' failed: Invalid argument
SIOCGMIIPHY on 'eth4' failed: Invalid argument
SIOCGMIIPHY on 'eth5' failed: Invalid argument
SIOCGMIIPHY on 'eth6' failed: Invalid argument
SIOCGMIIPHY on 'eth7' failed: Invalid argument
Das mii-tool wirft etwas aus, wenn Du es alleine ausführst? Du musst noch das Device bei einer Änderung angeben
Das mii-tool war das dabei ich hab das nemlich nicht install ?
Und was für eine Änderung muss ich noch angeben ?
@Jorge
Und das mii-tool funktioniert?
Ich hab für meine NIC im bootlog folgendes:
eth0: Setting 100mbps full-duplex based on auto-negotiated partner ability 45e1
mii-tool meint aber:
ldap:~ # mii-tool -v
eth0: 10 Mbit, half duplex, no link
product info: vendor 00:00:00, model 0 rev 0
basic mode: 10 Mbit, half duplex
basic status: no link
capabilities:
advertising:
ldap:~ #
:confused::confused::confused:
Manx
root@USER/$eth0: Setting 10mbps full dulex based auto-negotiated parner ability 45e1
bash: eth0:: command not found
was muss ich den machen das ich die auf 10 mbit full deulex stellen kann
Hi!
Wenn das mii-tool funktioniert:
Mit "mii-tool -v eth0" siehst Du in welchem Modus die Karte läuft.
Mit "mii-tool -v -F 10baseT-HD eth0" setzt Du sie in 10 Half Duplex"
Manx
Edit Fehler ausgebessert :)
$mii-tool -V eth1
mii-tool.c 1.9 2000/04/28 00:56:08 (David Hinds)
SIOCGMIIPHY on 'eth1' failed: Invalid argument
das kommt bei allen eth1 bis 7
$mii-tool -V -F 10baseT-HD eth0
mii-tool.c 1.9 2000/04/28 00:56:08 (David Hinds)
SIOCGMIIPHY on 'eth0' failed: Invalid argument
geht das den ?
... ich weiß nicht woran's bei Dir liegt?
Also bei mir anderer Rechner:
eth0: negotiated 100baseTx-HD, link ok
mail:~ # mii-tool -V
mii-tool.c 1.9 2000/04/28 00:56:08 (David Hinds)
eth0: negotiated 100baseTx-HD, link ok
mail:~ # mii-tool -v eth0
eth0: negotiated 100baseTx-HD, link ok
product info: vendor 00:05:be, model 8 rev 0
basic mode: autonegotiation enabled
basic status: autonegotiation complete, link ok
capabilities: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD
advertising: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD
link partner: 100baseTx-HD 10baseT-HD
mail:~ #
Manx
kp also das ist kernel 2.2.2 nnd das nent sich IPcop was da drauf ist www.ipcop.org
Powered by vBulletin® Version 4.2.5 Copyright ©2024 Adduco Digital e.K. und vBulletin Solutions, Inc. Alle Rechte vorbehalten.